This is not the "My laser is broken!!!" forum. Advanced technical discussion is for intelligent discussion pertaining to the advancement of laser technology.
Guys im looking towards the future as I have no plans on upgrading to a QM, in fact I plan on buying another fb3. You can buy cheap on the web...
Does anyone have a circuit that can be used to balance and adjust the analog RGB pallet signals in the analog world say if using a soundcard DAC or...
Does anyone know the exact function of each of the pots on this Viasho Driver please? There are 2 sets of pot's huddled together, 5 in total. ...
Hi everybody, quite some time ago I asked for high side laser diode driver designs and after some help from Steve built a first prototype of my...
When the case of the red diodes is connected to 5v and not electrically insulated it gives some inconvenience in isolating the red module from the...
Hi all, I have just spotted that surplusshed have brand new CTI 3200-142 AOM crystals including bragg mounts for $14ea! This raises two obvious...
Greetings from So. Cal. again,I have a Lasos LGN 7872-02F power supply,and an S.P. 163-A1202 Argon head. They do have mate together(cable-wise) and I...
I have now tried a couple different soundcard correction amps, laserboy and drlava's (EDIT: opening laserboy showed it is the same correction board)...
Hi guys, I'm a bit unsure wether I should use TECs in my mini RGB projector. I want to build a quality projector that I'm proud of but don't...
Anyone have any idea what diode might be used in this or if it's complete fiction? http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=180548223643...
Hi folks. i have an bare 100mW green module from Susie here, the ones for "own builds", without heatsink and only a click-on driver. I want to use...
Hi All, in light of the new 445nm diodes I am rebuilding my micro RGB with a bit more umph. Currently what is limiting me is finding a suitable...
Does anyone have specs for the following driver? Pin out, pots, anything would help.
Post links and discuss TEC drivers, TECS and sources for components! I found this in my archives: Elm-Chan TEC circuit with Atmel mcu...
On a Model: VD-II-L (power driver with safety lock), does anyone know what pot might adjust idle current? Turn on is well above where signal starts...
Hi guys, I’m after some advice on what optics to use for my mini RGB projector. I’m building this projector so I can practice LivePro while I’m...
Wondering what happens to LASER light if shaped with a simple drilled hole in a piece of black anodized aluminum. I can't believe what a brick 635...
OK,so I have a 163-A1202 argon head,and bought a Lasos Model: LGN7872-02 Input: 200-240 - 16A Max 50-60Hz Output: 70-150 VDC 3.5 - 9.0 A It...
Hi guys, does anybody have a schematic for the ALE YD-LS inrush board? I have the schematic for the YD-PS inrush board (from page 31 of the manual),...
Hi, can anyone help please i am thinking of purchasing this module are these specs good? Specifications: GXP-500 GXP-800 GXP-1000 ...
With the advent of super ubber powered home projectors, we are getting close to the level of power where the relflected light from the image is...
Hi all, I've just finished the 10 channel ILDA splitter for buffo. This will hopefully make a great addition to FLEM and SELEM meets. The...
I have a row of gradient index lens cylinders from a LED print head "laser" printer. They were almost-contact aligned with the LED strip and very...
were can i buy a +/-24volt switch mode psu?
Would anyone have a manual for a LaserMedia LM142DMX board? What I really need is the pinout information and DIP Switch indentification. Jim
Use this control to limit the display of threads to those newer than the specified time frame.
Allows you to choose the data by which the thread list will be sorted.
Order threads in...
Note: when sorting by date, 'descending order' will show the newest results first.
Forum Rules
