Have lasershow.ILD will travel ;) How the pros and hobbyists make a laser into airborn artwork!
hey everyone been a while since i last posted but it looks like the time is about here!! My schedule is now clearing up for a month so it looks like...
So Im deciding on a laser machine to buy, Its going to be used in a college dorm room with some fog and diffraction glasses. budget 250 max. I want...
Good evening good folks of PL, Looking into putting together a mechianic blanking system for a large beam dia projection system, 9-10mm. I would be...
I just purchased a DL-55+ (what is the difference between dl-55 and dl-55+) and am not using it with a dmx controler. My problem is that the beams...
I'm starting work on a new show with a band, and I want to have my lasers relatively low down (possibly near floor level). My tripod stand are...
can i use a usb audio dac with popelscan?
Just wondering if anyone here has any experience using the Light Converse visualizer software? http://lightconverse.net/ Now that it supports...
Hi, I've inherrited what was at one point a EULights.com (the no longer exist as far as I can tell) 150mW 252nm projector. It has an ATMEL...
Hey guys, So, as many of you know, I'm the A2 for Fiddler on the Roof. Once we're loaded in to a city, assuming nothing breaks, the run of the...
I lost my other thread somehow, but, I have finished my projector! I went in yesterday to try get some lighting clamps (SO I can mount it on...
Hey guys After a long time of designing, changing the design i,m almost at the end of building my second projector. Actually it looks a lot as my...
Well CRAP! Went out to my garage, fired up my laser, and found that my Y mirror on my Cambridge 6800HP mirror came off the shaft of my scanner, What...
Hi Folks, We are in the process of changing LivePRO a bit. Changes include some visual styling (something like "skin", but not really) and also...
If anyone needs manuals for their ML8-5G or ML8-5GX or their G-Scan I scanned them in after I got a request for them so figured I would share them...
Hi all, I seem to be getting a few enquiries for small outdoor displays. I have sufficient laser power for small localised events. The...
Well it's probably been done and talked about before but here is my attempt at it and I thought I would share it because I finally got it working...
Can someone provide me the pinout for the 9 pin input on the Cambridge 6580 Rev D amps? Thanks! Adam
I cobbled up a spreadsheet for the simplified MPE calculations. It's attached here for comments suggestions etc. Its pretty basic but might...
Hi everyone, A while back I seen someone's projector build, in the UK I believe, that had a small heating element with a fan inside the projector...
A little introduction to myself and some research on different ways to buy/build a projector (Hopefully this helps someone out there). ...
Im still pretty unclear about which optics ill for a RGB setup.. can someone verify that these parts are what i will need to get a scanner setup? or...
Hello people, So I'm going to build a USB interface DAC type thing out of an Arduino. As the Arduino runs at 8 bit I will need to increase...
Does anyone have any instructions on how to sync audio with a show in Quickshow for the FB3? The "QuickTimeline" tab has the import waveform...
I've got an older Pangolin QM2000 board that I'd like to use in Pangolin's nifty QM2000.net set up. Pangolin states that boards with serial numbers...
Hey folks, I posted a few questions before the festive season about how to drive my DT25 galvos, and since then things have been coming along....
Use this control to limit the display of threads to those newer than the specified time frame.
Allows you to choose the data by which the thread list will be sorted.
Order threads in...
Note: when sorting by date, 'descending order' will show the newest results first.
Forum Rules
