Page 1 of 2 12 LastLast
Results 1 to 10 of 12

Thread: Any Van de Graaff generator experts in here?

  1. #1
    Join Date
    May 2009
    Location
    CA
    Posts
    116

    Default Any Van de Graaff generator experts in here?

    I got most of the parts but not sure on the design. All the ones I've seen online have a large hole cut into the bottom of the sphere with the top pulley inside the sphere. I can't find any information that this in necessary. For ease on construction I thought I'd put the top pulley under the sphere in the support tube and run a wire from the comb to the inside of the sphere. Im going to try this idea this weekend, but wanted some input if I'm going the right direction.

    thanks
    Jason

    Click image for larger version. 

Name:	vandegraaff.jpg 
Views:	8 
Size:	131.7 KB 
ID:	51240

  2. #2
    Join Date
    May 2009
    Location
    Sacramento, California
    Posts
    608

    Default

    give it a shot and let us know how it works out.
    -Nate.
    Will there be three phase!!!!

  3. #3
    Join Date
    Jun 2010
    Location
    Blacksburg VA
    Posts
    137

    Default

    Electrostatics is fun! If you were East you could visit the Doctor's original generators at the Boston Museum of Science, they built a three story hall just for the display.
    The reason the takeoff is inside the top ball is so there's no electric field keeping the electrons from coming off the belt.
    All the electrons are gathering on the outside surface of the ball since they repel each other.
    If the takeoff is outside the ball, the electrons on the belt will also be repelled and won't build up anywhere near as much voltage.
    If the takeoff is inside the ball, the effective local voltage is zero and the electrons will keep coming off the belt until the air breaks down.
    In the case of the original, that's a 17 foot spark.

  4. #4
    Join Date
    May 2009
    Location
    CA
    Posts
    116

    Default

    Thanks Dan

    That makes more sense. Guess I'll need to figure out how to cut a 4" hole in one of the bowls. I'll post the progress.

  5. #5
    Join Date
    May 2007
    Location
    1 hr from everything in SoCal
    Posts
    2,753

    Default

    Quote Originally Posted by f150trk21 View Post
    Guess I'll need to figure out how to cut a 4" hole in one of the bowls.
    I would think a plasma cutter would work well. Make your initial cut and then clean it up with a file and "polish" with different grit sand paper.
    If you're the smartest person in the room, then you're in the wrong room.

  6. #6
    Join Date
    Dec 2008
    Location
    Canada
    Posts
    972

    Default

    A Dremel tool with a disk cutting blade may work.
    Or if the bowls are too large you can use a Die Grinder
    or Cut Off Grinder.

    Jerry
    See the LaserBee II and all other LaserBee LPM products here....
    All LaserBee Laser Power Meter Products

    New 3.2Watt RS232/USB LaserBee II LPM REVIEW


    Always in stock and ready to ship....
    Subsidary:-Pharma Electronic Solutions

  7. #7
    Join Date
    Jan 2006
    Location
    Charleston, SC
    Posts
    2,147,489,446

    Default

    Why not use a 4" hole saw? Stick it on the end of a drill and you're done in less than a minute.

    Here's a link to Home Depot, but I'm sure you can get one cheaper...

    Adam

    Edit: Here's one for $11.

  8. #8
    Join Date
    Nov 2008
    Location
    Cleveland Ohio
    Posts
    2,599

    Default

    Try a diamond hole saw. They sell them for cutting glass in fishtanks.
    http://www.bulkreefsupply.com/diamon...rill-bits.html

    The take off has to be inside for it to work. The charge builds up on the outside.
    The inside is a gauss cage with zero potential.
    If you want to really make it fly pull a vacuum inside the system.

    The ball can be made of almost anything. You can use a plastic ball covered in copper tape.
    You just need to make the top surface contact the inside by coating both side of the sphere and outside.
    IE tape both the inside and outside. Use the copper tape used for shielding guitars.
    I have not tried this but is sounds reasonable. It is only the surface that counts.

    http://www.stewmac.com/Pickups_and_E...All%20Products

    I prefer the whimshurst for electrostatics.
    Last edited by kecked; 12-04-2016 at 04:52.

  9. #9
    Join Date
    Jun 2008
    Location
    Orange County, CA
    Posts
    236

    Default

    Here is a site that shows the construction of a Van de Graaff generator and using a Dremel to cut the hole in the metal sphere:

    http://mark.rehorst.com/Van_de_Graaff/

    I would not recommend a hole saw from Home Depot since the teeth are too coarse.

  10. #10
    Join Date
    May 2009
    Location
    CA
    Posts
    116

    Default

    Thanks for the suggestions. After some measuring, I'll need a 4.75" hole and the bowl is stainless steel. I briefly tried a dremel with cutting wheel, but that would be very slow going and my bad hands aren't up to it. I do have a 10" drill press but it seems risky to put a 4.75" hole saw on it. Maybe I can find a machine shop that'll do it.

    thank
    Jason

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •