really unpleasure trade with Lasernerd

**Lasernerd** · 05-20-2009, 20:28

Originally Posted by bridge

but your picture clearly show the head had stand.
it is strange the head without stand.
if you don't had, that's ok, we can do it ourself.

No worries Bridge!!!
I will send you one since i am such a aweful guy!

umm we also have a middleman,,lets keep it there ok?Till all is done?
Like if you have more requests etc. batteries,cleaning cloth whatever

**bridge** · 05-20-2009, 20:48

Like if you have more requests etc. batteries,cleaning cloth whatever

No, Sir.

**drlava** · 05-20-2009, 23:06

Glad to see both of you working together again to settle this. Let's follow through with the plan and everyone comes out (of this part) a winner.

**Lasernerd** · 05-21-2009, 09:58

here is what I am shipping to our middleman..

See the FieldMax TOP that is for the middle man!
wel it is public now,,,Bridge do you like the PM10? there is the stand for the PM10,your welcome

That meter is not for you,,It is for the middle man as a gift for his troubles

I must REPEAT the meter is for Andrew ONLY not Bridge is that clear?

And the head is used as per our agreement,this has the same specs but is visualy pretty,,cool happy? is this good for you Bridge?

**bridge** · 05-29-2009, 11:11

Hi Andrew,
how are you?
had you received the powermeter head from Lasernerd?
any news from you is great thanks!
Best regards!
Bridge

**drlava** · 05-29-2009, 11:25

Hi Bridge,
Lasernerd and I have had good communication so far, he will ship today or Monday I expect.
As you can see, the sensor surface looks clean in this photo, you will receive more photos and testing report from me when it arrives. I have just re-calibrated my Scientech meter for measurement comparison.
Lasernerd, feel free to post or email when it has been sent.
thank you all.

**Lasernerd** · 06-04-2009, 09:35

has beed delivered

**drlava** · 06-04-2009, 10:54

Hello Lasernerd and Bridge,

I have picked up the package, and everything appears to be in order. The parts were well padded and individually wrapped. Included is the sensor Coherent PowerMax Model PM10, a stand, and the FieldMax TOP meter. Sensor surface is as shown in Lasernerd's photo. The meter appears to accept a common 12V co-axial power connector and also can be powered by common AA batteries, so testing won't be a problem. Initial power-up went fine and testing will take place later tonight.

**Laser Ben** · 06-04-2009, 14:13

I would be careful. Most of the coherent products have a center grounded connector for the power. I found that out the hard way. Please check into this before you just plug something in.

**drlava** · 06-04-2009, 14:35

Originally Posted by Laser Ben

I would be careful. Most of the coherent products have a center grounded connector for the power. I found that out the hard way. Please check into this before you just plug something in.

Thanks for the warning. In this case, the power input polarity is marked right on the unit 12V, 1.25A max draw, tip positive. But I'm using batteries

**Laser Ben** · 06-04-2009, 14:43

Ah okay, good deal!

**drlava** · 06-04-2009, 22:06

Ok, tests are in

I used 650nm and 405nm to cover the wavelength range with available direct-injections diodes for power output stability for comparison. For the FieldMax, the proper wavelength was entered in the meter and the device read the calibration offset from the chip in the sensor connector for fine tuning. The test wavelengths were not extreme to the broadband sensor coating so for these tests the tuning offset was minimal.

658nm:
Scientech 1: 220
Scientech 2: 215
FieldMax: 215

650nm:
Scientech 1: 57.2
Scientech 2: 55.5
FieldMax: 55.4

405nm:
Scientech 1: 59.7
Scientech 2: 58.4
FieldMax: 58.5

The fieldmax sensor was factory calibrated in 2006, the measurements appear to be right on. If anything the Scientech 1 is probably reading a little high, but all measurements agreed with error under 3.5%.

In the pics you will see some tape residue on the head, the tape was used to protect the sensor surface during shipping. The residue can be cleaned off with a little solvent.

The stand is a thorlabs branded item, appears to take a standard 1/2" dia. mount that will thread into the head. Bridge if you need one I can go down to our local surplus and look for one for you.

So, those are the results, what do you think bridge, time to complete the exchange?

**Lasernerd** · 06-04-2009, 23:33

Thank you Dr.Lava!

**bridge** · 06-05-2009, 06:49

thanks for informations and did compare test for us, Mr Drlava.

Bridge if you need one I can go down to our local surplus and look for one for you.

if you 'd like, that will be great thanks here.
if not, we also can do it here, thanks.
ok, we believe you, Drlava, I believe this one is better than before unit,

.
now let do second step.
Best regards!
Bridge

**drlava** · 06-26-2009, 22:16

Hello, tracking indicates the replacement head was delivered to Bridge on the 25th.

**laserbot** · 08-13-2011, 02:47

never buy from Mark Kriska. He gave me so much hell, I had to get the FBI involved. Hate that guy.

**bridge** · 08-13-2011, 03:27

I am sorry to hear that, Laserbot, wish FBI will help you. I thought Mark should disappear from the froums, but look like he still here.

Originally Posted by laserbot

never buy from Mark Kriska. He gave me so much hell, I had to get the FBI involved. Hate that guy.

**lasersbee** · 08-20-2011, 10:19

Originally Posted by laserbot

never buy from Mark Kriska. He gave me so much hell, I had to get the FBI involved. Hate that guy.

I just saw this... Here's a Heads UP....

You need to read the Date of the last post before yours...
The Member was Clue-By-Foured (banned) 2 years ago...
You are posting on a 2 year old dead Thread...

It's called Necroposting....

Jerry

**soforene** · 08-20-2011, 11:20

Originally Posted by lasersbee

...It's called Necroposting....

Maybe by you but I personally call it slaptaptingtong.

Funny how we make up names for stuff, isn't it.

Attachment 26693

**absolom7691** · 08-20-2011, 18:17

Soforene, good sir,

It is HIGH time you change your avatar. That was part of the fun coming to PL. "What is his avatar today? Bouncing boobs, kid falling off of *insert object here*...?"

**soforene** · 08-21-2011, 14:25

One can only apologize.

The selected avatar reflected a stage in my life currently being experienced (probably only recognisable to UK Members).

I shall endeavour to increase the quotient of joy and contentment to the forum from now on (even if it is by just leaving.....)

**absolom7691** · 08-22-2011, 16:51

There we go!

Yeah, I did not get what your previous one was. TV show in the UK?

Thread: really unpleasure trade with Lasernerd

Thread Tools

Posting Permissions