Activity Stream

;) ;) "That ain't workin'.....that's the way we do it. Get your mirrors for nothing...get your photons for a fee."

I love this thread, I am not worthy... Below is a little "In House" joke... Steve

Drawing came Late... See attached,,,, ~ Yes, I'm having a little fun with my response... But for beginners in electronics, its sort of how you think at the start. ~ There is a E-book for Kindle etc of Bill Benner's book for like 99 cents... Suggest you buy it... LASER SCANNERS:...

Controlling values with the panel protocol does not allow the changing of by specific amounts because it is just simulating knobs being turned. It is necessary to use the MIDI protocol if you want to set specific values.

Gotcha, thanks. ...Mike

It hadn't occurred to me that wasn't in the manual. It's fairly similar to a lot of tap to time functions on lighting desks that I use, so I think I just saw the 'tap' word and realised it was a dual action button, so probably modified by the shift key. And it was!

Yes, I raised this with Chris on Messenger the first night I used my Radiator. I've heard it mentioned elsewhere too, so I'm sure its well on their radar. In terms of the screen, would one solution be to send the screen out of the HDMI port to an external monitor? Obviously you'd have to...

It is my pleasure to share this information, as well as rewarding to know it is appreciated by others. I had noticed in another thread of mine where I provided YouTube links that one link was no longer viable. I've repaired that link today. The thread was here...

The coolest thread on PL. Thanks for sharing all of this really intricate details of your projector. It is a treat!

I found a strange behaviour: When I control the preset buttons via network, all is fine: cat ./choose_preset |nc 10.0.0.23 4815 switches to the fifth preset(starting count from zero) , with choose_preset containing (OS X's hexdump): dirk➜~» xxd ./choose_preset ...

No, not without the resistors Steve drawing coming soon.. Steve

There are, but as BLDC motors you have to build a driver. I sent a couple of driver chips. (I picked them up years ago before they became 750 unit min order qtys, and I have fewer than I have motors. They require 6 external transistors - 2 for each coil and they're surface mount - so bread boarding...

Are there any left? ...Mike

... some images and name/version maybe? There are a bunch of different types and softwares around ... Viktor

You are welcome.

xxxxxxxxxxxxxxxxxx thank you very much-- these are incredible little motors.. kind of you to give them. hak

Thank you Sir!!!!!!

Thank you Steve!

Greg, check your email for circuit fragment images. You'll need a quad npn on a chip Steve

Oh boxes and blobs, the panel is upside down.

If that's looking a little different than you remember, you might have the panel upside down... the EAO switches are a little unusual. Each bank has a N.O. & a N.C. set of contacts.

The CYGN-B is almost complete. It's a trip to have my fingers on these marvelous taps after forty years of reviewing distant memories. Metaphors such as Rosetta Stones and Holy Grails apply to this project, at least on a personal emotional level. Gently easing the scratchiness out of the dials......

Hello, on the Radiator, in the three LFO sections, there is a line (TAP) right under the enable Button for each LFO. If You hold the SHIFT Button and tap in a Music beat on this button the LFO will pick it up. My piano metronome ranges from 40 to 240 Ticks per minute, and the frequency...

Here's a little Black Fourday discount to help you get a Radiator ;)

Iam searching economic optic fiber LLK-D 200um . The laser is compatible with this type of fiber.

Thanks for the schematic, i am rather new to electronics so i made a little drawing, would this be the correct wiring? is it also correct to wire gnd to pin 25? and not exactly sure where i should put resistors and what value