Massive For Sale thread - Lots of stuff

[andy_con]

I have a number of for sale threads listing different things, found some more stuff today so from today all other threads are closed and im making this one big thread.

All prices are subject to postage and paypal fees, if oaying via PP.


first I have a 1000mw 638nm red module for sale

fully sealed housing with AR window, d-sub connector at the back.

measures 66mm wide by 141mm long by 44mm high

beam is about 3.5mm by 3.5mm at aperture @ around 1.3mR as with most of these 638 builds the beam is a little messy at distance

module runs on 5v @ 3amps

open to offers around £500 + postage
















next I have a 3.5w 445nm module

fully sealed housing with AR window, d-sub connector at the back.

measures 66mm wide by 141mm long by 44mm high

beam is about 5mm by 5mm at aperture @ around 1.2mR

module runs on 12v @ 4amps

open to offers around £450 + postage

















1000mw 660nm module

it uses open can red diodes with optima lens
beam is 3.5mm by 3.5mm @ 0.6mR so mega tight

perfect for graphic shows, its a fully sealed module with an AR window

module size is 141mm by 66mm and around 50mm high

would accept around £350













Brand new empty PSU case
It measures 190x140mm
£20











1000mw 638nm laser module

Brand new with 0 hours on the clock, it contains 2x 500mw diodes. They are combined through a cube so the end result is a nice big cross
Runs on 12v
There is an AR window on the module, im not sure why as there is a fan on the side blowing dust in?
Module measures 80x55mm

£100








projector case measuring 340mm L x 330mm W x 250mm H

both lower and upper ally base plates are 12mm thick so nice and stable and good for heat sinking

as you can see plenty of room for lasers. on the lower deck are a 5v 8amp psu and 12v 8amp psu, which feeds into that connector at top.
all holes in the base plates were done on my mill so nice and tidy.
the projector has a machined holder for a 3mm thick AR glass window from edmund optics and draft excluder round the case. all fans have dust filters on them.
also I have a wind up stand and a 30m ILDA cable. stand goes up to 3m in height. the arm for the stand is not bolted to the projector in the photos in case your wondering. can be sold with the case as well, as they are designed to go together

I would accept £150 for the case alone and £250 for case with stand the ilda cable










projector case measuring 300mm L x 330mm W x 230mm H

both lower and upper ally base plates are 12mm thick so nice and stable and good for heat sinking

as you can see plently of room for red and blue, on the lower deck are a 5v 8amp psu and 12v 20amp psu, which feeds into that connector on the top deck.
all holes in the base plates were done on my mill so nice and tidy.
the projector is sealed with a 3mm thick AR glass window from edmund optics and draft excluder round the case. all fans have dust filters on them.
also as an option I have a a wind up stand and a 30m ILDA cable. stand goes up to 3m in height. the arm for the stand is not bolted to the projector in the photos in case your wondering

the projector has custom machined fan guards on it, long storey dont ask

I would accept £150 for the case alone and £250 for case with stand the ilda cable











445nm waveplate originally from daves GB
comes in a ally holder so you can rotate the waveplate then lock in position
Can easily be removed from ally holder and round holder so its just a bare waveplate
£28






projector case measuring are 250mm L x 195mm W x 110mm H

10mm thick ally base plate and the projector is fan cooled (with dust filter)
although there isnt one there i machined the projector aperture to take a 2inch square AR 3mm thick glass windows from edmund optics
the case is sealed using rubber draft excluder

would accept £100 for it








got 5x digital thermometers up for grabs

full details here, as you can see they are new and have not been used

http://www.ebay.co.uk/itm/5V-Digital...item4178122480





clearing out some old stock and I have some 5.6mm and 9mm aluminium diode holders for sale

16mm wide, beam height of 15mm.
tapped for a m9x0.5 lens
2x tapped m3 mounting holes on the bottom.

I only have 16 backs though

probably not suitable for 2mm FL lens as they aren't accurate enough

£8 each + delivery

[Bradfo69]

That damn 1 watt 660 still is haunting me.

One the first case listed, is the aluminum riser for the scanner galvos designed for the DT40wides? I'm thinking about the whole case but, at that same time, also thinking that since you have a mill... what would it cost me to make 3 or 4 of them (the risers).

~B

[andy_con]

Its designed for dt30, are dt40w the same mounting block?

I have lots on at the moment mate and wouldn't like. To say when I could make you something, sorry

[dave]

Sorry to jump on your thread Andy, but.....

I have a similar aluminium riser arriving early this week ( actually 100pcs all anodised black) to suit DT30, DT40pro, DT40w's . Brad - hit me up

That damn 1 watt 660 still is haunting me.

One the first case listed, is the aluminum riser for the scanner galvos designed for the DT40wides? I'm thinking about the whole case but, at that same time, also thinking that since you have a mill... what would it cost me to make 3 or 4 of them (the risers).

~B

[andy_con]

first post updated, a few bits sold and removed.

DT30 scanners added

[hobbybob]

I want the Blue PBS cube for 15 quid. Save it for me, i'll take it of your hands in April on the LEM ok ?
If you need money now, i can transfer it to the bt adress i have used before. let me know chop!

[andy_con]

big price drop on all modules

[Bradfo69]

Hoping for a little more disposable income soon. (The weddings will be starting back up and I'll have some extra to "play" with.) Don't worry... I have been popping into the thread every now and again just to check on my 660 and make sure she's still ok.

I think I seriously need to sell some existing stuff and do some "restructuring".

[andy_con]

make it happen

[epyn]

PM sent got it?
Ferenc