Projector Capabilities Poll

[DixiScan]

My DIY:

+ 500mW 635nm red, analog mod and differential ended
+ 300mW 532nm green, analog mod and differential ended
+ 250mW 473nm blue, analog mod and differential ended

+ 50Kpps scanner from Laserworld
+ Safety Board from Laserworld
+ Interlock by pushbutton with key to unlock

+ no ground pins are used!
+ no single edged pins used!

+ build-in Easylase interface
+ 2nd ILDA input (for e.g. QM2000.Net, Moncha interface)
+ input manual selectable during show playback
+ weight balanced case for truss

+ software:
+ Pangolin LD2000 Basic, LivePro,
+ Mamba v2.1
+ HE-Laserscan v4.1
+ Moncha v2.10

[allthatwhichis]

Kvant 1W Spectrum RGB projector

Technical specification:
Dimensions:264 x 175 x 180 mm
Weight:ca 8,5kg

Input power:230VAC (±5%), 50Hz, 110VAC, 50Hz, 400VA max.
Optical output power:1W

Input :ILDA DB25 Male,
Input scanning voltage:±5V/balanced

CT 6215 scanning system:Scanning angle: 60° for both axes Scanrate: min.40kpps*
(I run em at 30kpps, 25°)

Blanking:0-5V analog, up to 50 kHz, TTL
Ambient temperature:0 - 50°C
Ambient operation temperature:10 - 35°C

Red Wavelength [nm]:640 Power [mW]:300
Beam diameter [mm]:2
Beam divergence [mrad]:<1

Green Wavelength [nm]:532 Power [mW]:300
Beam diameter [mm]:2
Beam divergence [mrad]:<1

BlueWavelength [nm]:445 Power [mW]:500
Beam diameter [mm]:2
Beam divergence [mrad]:<1

Pictures, review...

[mccarrot]

Do you like the laserworld safetyboard? and is there a manual available?

[oliverst14@hotmail.com]

2 x 200mw 532 nm greenies with ttl modulation and 30kpps not sure what manufacturer ilda controlled

1 x 450mw rgb 50mw green 532nm 50mw blue 473nm 350mw red 650nm all running way lower than spec due to it being rubbish big dipper stuff and 10k scanners. strange system using ethernet connectors for ilda but can be ilda controlled all ttl modulation

1 x 450mw rgy 150mw green 532nm 300mw red 650nm and dt 25s diodes analouge modulation and ttl

1 x 450mw rgb actually quoted tested and running at 600mw but only quoted not tested myself. 100mw green 532 nm 50mw blue 473nm and 300mw red 650nm using 30k scanners not sure but think there space las scanners all analouge modulation and ttl. this thing looks a hell of alot brighter than the rated specs but hope it hasnt been tweaked with to run higher as this will decrease diode life still ok though

also have a 300mw 532 laserwave diode and a set of scan pro 20s with a 640nm 450mw in the post from marc (gottaluvlasers)

[Xytrell]

20kpps
635 analog
532 analog
473 analog
ILDA/USB

[Mr.Coffee]

100mw (140mw cw) 473 laser-wave
just purchased:
200mw 532 (lasever, but too cheap to pass up)

Dt-40 pros pango modded & tuned
La freak FB3

the cheapest case I could find to get it across the pond. (will be up for sale in the near future, actually)

[cfavreau]

What is "pango modded & tuned" for your DT-40 pros?

[Mr.Coffee]

There's a mod for the dt 40 pro galvos, basically removing the notch filter. I'm not sure if Jian has addressed this issue in his recent mods or not, but it used to be something that would improve the response a little, as the filter was unnecessary on that particular board. Bill will also tune your galvos for free if you ship them to him (provided you ask him nicely, of course). He's really good at tuning scanners, and will get the most out of them. Also, when I shipped them, they came back with a db-25 wired up to them, which made putting my projector together much easier.

[Shone]

I think you should try sensors in your projector or other products. South Ocean Sensor - Load Cells & Sensors Manufacturer and provide all kinds of sensors which are used for different purposes.

[cfavreau]

What are you talking about? Well I know what you are talking about however what does that have to do with the price of tea in China?