DIYDRONES.com
Arduinopilot.
Steve
DIYDRONES.com
Arduinopilot.
Steve
Too much data on R/C input which I don't want to use. Im not making a vehicle, but a camera stabilization platform. I joined DIYdrones a while ago and have found nothing to help, directly
405nm (500-750mW) , 445nm 500 to 2750mW) , 473nm DPSS, 532nm DPSS (80 to 3000mW) & 635nm (250mW) OEM Lasers
Visiblediodelasers.com
10% Off Website lasers for PL members - PM or E-mail me.
CW, TTL & Analog Modulation available
Custom / Turnkey OEM systems available
Laser Diode Power Supplies (CW & Modulated) to 4 Amps
Beam-shaping optics available (Prism Pairs)
NEW - Laser Diode / Heat sink Mounts
You have to start with a open source inertial platform, hence DIY drones.
If you cannot adapt their open code, there is almost NOTHING else available for what you seek, short of paying for commercial IMU.
Steve
I got it, just had to work hard and look more. I think I need to add a third axis for yaw rate on camera, but here is the viseo of it working..
http://youtu.be/uN6O62puMz8
405nm (500-750mW) , 445nm 500 to 2750mW) , 473nm DPSS, 532nm DPSS (80 to 3000mW) & 635nm (250mW) OEM Lasers
Visiblediodelasers.com
10% Off Website lasers for PL members - PM or E-mail me.
CW, TTL & Analog Modulation available
Custom / Turnkey OEM systems available
Laser Diode Power Supplies (CW & Modulated) to 4 Amps
Beam-shaping optics available (Prism Pairs)
NEW - Laser Diode / Heat sink Mounts
what about this:
http://www.youtube.com/watch?v=J6HDUDbeEJw
See the LaserBee II and all other LaserBee LPM products here....
All LaserBee Laser Power Meter Products
New 3.2Watt RS232/USB LaserBee II LPM REVIEW
Always in stock and ready to ship....
Subsidary:-Pharma Electronic Solutions
405nm (500-750mW) , 445nm 500 to 2750mW) , 473nm DPSS, 532nm DPSS (80 to 3000mW) & 635nm (250mW) OEM Lasers
Visiblediodelasers.com
10% Off Website lasers for PL members - PM or E-mail me.
CW, TTL & Analog Modulation available
Custom / Turnkey OEM systems available
Laser Diode Power Supplies (CW & Modulated) to 4 Amps
Beam-shaping optics available (Prism Pairs)
NEW - Laser Diode / Heat sink Mounts
I need to reduce the time for servo response. It seems to work having the accelerometer on the base, rather than the top of the camera. Ill probably end up using better gear motors with tach/encoder feedback. Ultimately, Ill have it all machined...In the mean time, atleast it works
405nm (500-750mW) , 445nm 500 to 2750mW) , 473nm DPSS, 532nm DPSS (80 to 3000mW) & 635nm (250mW) OEM Lasers
Visiblediodelasers.com
10% Off Website lasers for PL members - PM or E-mail me.
CW, TTL & Analog Modulation available
Custom / Turnkey OEM systems available
Laser Diode Power Supplies (CW & Modulated) to 4 Amps
Beam-shaping optics available (Prism Pairs)
NEW - Laser Diode / Heat sink Mounts
here is the one I will be using on my HEXACOPTER :
http://www.youtube.com/watch?feature...&v=BFOn3_pjKiQ
Made by stepping motors
pretty stable if u ask me
Nice to have that sort of $$ for it is not cheap. Servos, steppers or gear driven with encoders. If servos, they're not the cheap aircraft ones. I've seen RS232 / RS485 operated servos, very expensive ~$500usd each whhich would be easy to design with..
405nm (500-750mW) , 445nm 500 to 2750mW) , 473nm DPSS, 532nm DPSS (80 to 3000mW) & 635nm (250mW) OEM Lasers
Visiblediodelasers.com
10% Off Website lasers for PL members - PM or E-mail me.
CW, TTL & Analog Modulation available
Custom / Turnkey OEM systems available
Laser Diode Power Supplies (CW & Modulated) to 4 Amps
Beam-shaping optics available (Prism Pairs)
NEW - Laser Diode / Heat sink Mounts